Documentation
Configuration
First you should enter global parameters.
| Title | The title of your project |
| Description | Here you can enter a small description of your project |
| Title and Description will be displayed in the overview accordingly | |
| Load Balancing | Activate load management. Note on the cFos Power Brain Wallbox: If you operate the wallbox standalone or as a master, activate the load management. This will also enable you to use all the extended functions. If you operate the wallbox from another load management system or as a slave, deactivate the load management (mode: Observe). |
| Max. Total current per phase (mA) | Determines the maximum available electricity that the house connection can provide. This current is available to the house, including all consumers and charging stations. You can either enter a fixed value or a formula here. This allows you to make the available house connection current dependent on switching inputs (e.g. for a ripple control receiver) or Charging Manager variables (which can be set externally via HTTP API). |
| Current reserve (mA) | Power reserve that the control system attempts to reserve. You must dimension the value so that load peaks do not cause the fuses to trip. The reserve should be selected higher, the less information is available about the utilisation of the individual phases (through suitable meters). |
| Overdraft | In the "Overdraft" field, the Charging Manager enters the maximum value of the overdraft in milliamperes that has been seen so far and exceeds the reserve. This allows you to see later how well the regulation is working and whether you should set more power reserve. Ideally, the overdraft should be and remain 0. You can set this historical value back to 0. If the cFos Charging Manager detects an overdraw (this can be lower than the historical maximum), it reduces the available charging current by the overdraw current for 5 minutes to allow the fuse to cool down. This is displayed in red on the dashboard as an overdraw. |
| Share of total electricity (%) | This can be used to temporarily reduce the usable portion of the maximum total current. This value is not saved. |
| Max. Total wallbox current (mA) | Depending on the house installation, an additional power line may have been laid for the charging stations exclusively for charging electric cars. "Max. Total wallbox current" determines the maximum current of this line |
| System voltage | It should normally say 230V here |
| Max. Phase imbalance (mA) | The maximum phase shift load permitted by the energy supplier (i.e. one-sided phase utilisation, e.g. for single-phase charging cars). The prescribed value is 4600 W, i.e. 20 A. Your energy supplier may allow you a higher unbalanced load. |
| Skew incl. consumption | Activated: The skew is calculated incl. all consumers and producers. Deactivated: The skew is only related to the charging cars. |
| Duration of a charging pause (s) | Minimum length of a break. This is important to protect devices and avoid fluctuations. |
| Delay for switching to 3-phase (s) | Time in which sufficient power must be available for 3-phase charging before switching over. |
| Reduce charging power in the event of a COM error | If the wallbox is unavailable for more than 3 minutes, its last known charging power is counted as an external load and deducted from the total power available for charging. |
| For device deactivation | the wallbox is deactivated in the Charging Manager Setup, charging can either be deactivated, the minimum charging current can be set or all charging limits for this wallbox can be cancelled. |
| For device deactivation | How should a device be set (if possible) if the cFos Charging Manager relinquishes control over it? Options: Disable charging, minimum charging current, remove all limits (equivalent to OCPP free charging). |
| Energy provider | Here you can select the energy provider used for price-based charging rules. For Tibber, you still need an OAuth2 token on the configuration page. |
| Formula for solar surplus | Here you can enter a formula that calculates the PV surplus instead of the Charging Manager's standard calculation. Note: You can use CM._org_surplus to determine which value the Charging Manager would have used as the PV surplus. |
| OCPP Server TLS | Enable, disable or auto detect TLS |
| OCPP Server Port | TCP/IP port of the OCPP server in the cFos Charging Manager |
| OCPP Server Password | Password for logging on to the OCPP server |
| Use own certificates | If activated, an SSL certificate that you can upload under Configuration is used. If deactivated, a self-signed standard certificate is used. |
Add new devices
Press the button "Add New Meter" to add another intermediate meter. You can set the following values for a meter:
| enabled | The checkbox decides whether the device is enabled (i.e. the Charging Manager controls it or reads it out) or whether it should only be stored for later use |
| Number | This is a freely selectable number that is displayed in the overview, e.g. the number of the parking space whose consumption is to be measured |
| Name | Here you can give the intermediate meter a name |
| Description | Here you can add a small description |
| Device type | Use this selection list to specify which device is involved. The Charging Manager supports a range of different devices. We will expand the list of supported devices over time. The supported devices include an S0 intermediate meter, which you can connect to one of the two inputs of the cFos Power Brain Controller. There are also other common intermediate meters and virtual meters to choose from. The virtual counters are internal Charging Manager counters that totalise certain power values so that they can be displayed nicely in the overview. There are also simulated counters for experimentation. You must set the following for the counter: |
| Address | With the destination address, you tell the Charging Manager how to address the unit. You can either specify an IP address:port or an HTTP, an HTTPS URL or a COM port and then the COM parameters, e.g. COM1,9600,8,n,1. |
| ID | If the device is a Modbus device, you must enter the Modbus Slave ID of the device here |
| Role | This selection list decides what role the meter has. "Display" means that the meter is for display purposes only and is not included in power calculations. "Consumption" means that the meter measures the power of a consumer. This is subtracted from the set house connection power. With "Generation" you set up meters that measure generated power (e.g. from a solar system). This power is added to the existing house connection power and is available to the wallboxes as charging power. Instead of individual generation and consumption meters, you can also install a central meter for your house connection. In this case, set "Role" to "Grid reference". The Charging Manager then ensures that the total consumption does not exceed that of your house connection. In this case, you do not need to define any consumption or production meters. Meters with "Role" "Consumption E-car" record the consumption of electric cars and are usually attached to a Wallbox. "Storage Home" is a storage that may not be used during PV overcharging. "Storage All" is a storage device that may also be used for charging. |
| Factor | Allows you to integrate the meters with transformer coils. You can enter the transformer factor here if the counter does not calculate it into the values itself. To invert a meter you can specify a negative sign (e.g. if the meter was installed "upside down" you can specify -1.0). Note: Both consumption and generation meters normally have positive power values. The role decides whether a value is subtracted from or added to the house connection power. In the case of the total meter, a positive power reading means consumption, a negative feed-in |
| Phases | The phases that the meter uses or 'automatically' detects based on meter values when charging. |
| Adjust current values | For advanced configurations: Here you can add something to the current values with a formula. If, for example, you have a meter that counts consumption plus the wallbox, you can subtract the current of the meter for the wallbox to determine the pure consumption. |
| Hide device | If ticked, do not show as tile (unless "show all devices" is selected). |
| Show in overview | If ticked, show in the dashboard below the chart. |
| Publish info via MQTT | For this device, the current values are published via MQTT. |
| Publish device info via Modbus | For this unit, the current values are published via Modbus server. |
| Record measurements | For this unit, the current values are recorded to be displayed as a diagram, if necessary. |
| Show diagram for unit | For this unit, the measurement data is displayed in a diagram. |
| Show in overview diagram | For this unit, the measurement data is shown in the overview diagram in the dashboard. |
| Battery storage control | Here are the instructions for controlling battery storage systems using charging rules. |
| Remote maintenance | If the meter has a web UI, you will be redirected to it when you click the "Remote maintenance" button |
| Alternative method | If the forwarding does not work, you can choose an alternative method. |
Note: By the way, solar inverters also count as meters. These can often output the currently generated power via Modbus TCP, just like a meter.
Press the button "Add New EVSE" to add another charging station. You can set the following values for a charging station:
| enabled | The checkbox decides whether the device is enabled (i.e. the Charging Manager controls it or reads it out) or whether it should only be stored for later use |
| Switch to single-phase - only cFos Power Brain Wallbox | Here you can switch the wallbox to single-phase or three-phase. However, if you have activated automatic phase switching, the value selected here may be overwritten. |
| Number | This is a freely selectable number that is displayed in the overview, e.g. the number of the parking space whose consumption is to be measured |
| Name | Here you can give the intermediate meter a name |
| Description | Here you can add a small description |
| Label | A freely selectable lettering that appears in the overview when a vehicle is plugged in. If you select "User", the name of the user or the name on the RFID card is displayed. |
| Fixed RFID | If no RFID reader is available, a fixed RFID (mainly for OCPP) can be set here. |
| Device type | Use this select box to select which device it is. The Charging Manager supports a number of different devices. We will expand the list of supported devices over time. Among the supported devices is the cFos Power Brain Wallbox. You will also find other common EVSEs and a simulation for experiments. For the EVSE you have to set the following: |
| Address | With the target address, you tell the Charging Manager how it should address the device. You can either enter an IP address:port or an HTTP, an HTTPS URL or a COM port and then the COM parameters, e.g. COM1,9600,8,n,1. For OCPP, enter the Charge Point ID of the wallbox here. For cFos Power Brain wallboxes, you can also enter # and the serial number instead of the address, e.g. #W00-1234. cFos Charging Manager then searches for these wallboxes in the local network. This means that it will find them even if the address has changed. In larger installations, this also allows a prefabricated configuration to be used. The electrician then installs the wallbox with the correct serial number for each car park. The load management system then imports the preconfigured configuration based on the serial numbers, including names and numbers for the car parks, so that practically no configuration work is required on site for load management. |
| ID | If the device is a Modbus device, you must enter the Modbus Slave ID of the device here. If the unit is an OCPP unit, enter the Plug ID here |
| Pinned counter | If a wallbox does not have its own meter, you can "pin" a meter to it. The Charging Manager then assigns this meter to the selected wallbox and considers the power and energy information as that of the corresponding wallbox. Only meters with the "role" "consumption e-car" can be pinned. |
| Failsafe charging current (mA) - Only for cFos Power Brain wallboxes | If the wallbox goes into fail-safe mode for more than 3 minutes after a communication failure, the charging current to be used can be set here. 0 = deactivate charging, 1 = use the set minimum charging current. |
| Min. charging current | The minimum charge current below which charging is deactivated and a 300sec pause is initiated. Specified in mA. Minimum 6000mA, min. 6A. Some cars need more to start charging, e.g. Zoe 8A, Landrover possibly 9A. |
| Max. Charging current | The maximum charging current per phase in mA. that this wallbox supports or a formula. You can use the formula to limit the charging current dynamically. Application e.g. in an apartment building with wallboxes behind the flat meters. |
| Priority | Priority when charging. The default is 1. Higher priorities receive all available charging current first, followed by the wallboxes with the lower priority. |
| Phase rotation | The Charging Manager can detect phase imbalances (unbalanced loads) (provided the wallboxes have corresponding meters or meters are connected that can output the current of the individual phases). If the unbalanced load exceeds 4.5kW, the Charging Manager reduces the charging current of this charging station or temporarily switches off the charging completely until the symmetry is restored. If you want to charge several vehicles at different wallboxes, the phase position should be rotated during installation in contrast to other wallboxes. You can set this phase rotation here. Recommendation: Make it uniform, e.g. 1st EVSE 0 degrees, 2nd EVSE 120 degrees, 3rd EVSE 240 degrees, 4th EVSE again 0 degrees, etc. Note: The phase rotation refers to the phase rotation between the wallbox and the main building phases. Meter and wallbox must always have the same phase rotation. This should always be the case for meters installed in wallboxes, while you should pay attention to this when installing external meters. The display of the phases in the selection box in the web interface tells you to which phases of the building installation the 3 phases of the wallbox refer, e.g. at 120 degrees, L2,L3,L1 the wallbox phases L1,L2,L3 are connected to the building phases L2,L3,L1. This means that if, for example, a car is charging on phase L1 and the wallbox is connected with phase rotation 120 degrees, phase L2 in the building is loaded and displayed in the web interface. |
| Phases | The phases that the wallbox uses or 'determine' Recognise using phase-related meter values during charging. |
| Automatic phase switching - only for cFos Power Brain wallboxes | If possible, automatic switching between 1-phase and 3-phase in order to better utilise the PV surplus in the event of excess charging or, in the event of normal load management, to attempt to charge if sufficient power is still available on individual phases. |
| Wake up car | The cFos Charging Manager tries to wake up the car if it is not charging. This is currently only possible with the cFos Power Brain Wallbox under Modbus. |
| Let the car sleep | Some cars do not fall asleep at the end of the charging process and then consume power from the 12V battery. The cFos Charging Manager tries to detect this and prevent constant recharging. |
| Save battery | If your car always charges the battery to 100%, the cFos Charging Manager can stop charging as soon as the charging current falls below a certain threshold. Charging is stopped when the specified threshold is exceeded for min 1 min and then below the threshold for 30sec. |
| Save battery 2 | If your car always charges the battery to 100%, the cFos Charging Manager may stop charging as soon as the charging current drops below this threshold for longer than 60sec. |
| Keep loading activated | For wallboxes that no longer display meaningful status values when charging is deactivated. |
| Charging current offset (mA) | This can help the Charging Manager control if the car always uses less than the offered charging current. The Charging Manager then always gives this car the additional offset set here. |
| Hide device | If ticked, do not show as tile (unless "show all devices" is selected). |
| Show in overview | If ticked, show in the dashboard below the chart. |
| Publish info via MQTT | For this device, the current values are published via MQTT. |
| Publish device info via Modbus | For this unit, the current values are published via Modbus server. |
| Record measurements | For this unit, the current values are recorded to be displayed as a diagram, if necessary. |
| Show diagram for unit | For this unit, the measurement data is displayed in a diagram. |
| Show in overview diagram | For this unit, the measurement data is shown in the overview diagram in the dashboard. |
| Signed data | "Save external signed meter readings": If the wallbox provides digitally signed meter readings (calibration law), these are saved with the data on the charging process. "Sign and save internal meter readings": You can save your own digitally signed meter readings for the charging processes if the wallbox does not provide them (no calibration right). Here you will find further explanations on calibration law. |
| OCPP Gateway URL | OCPP Gateway Mode: The URL to which the cFos Charging Manager forwards OCPP communication to the backend. |
| OCPP Gateway Password | OCPP Gateway Mode: The password for the OCPP backend. |
| OCPP Gateway Client ID | OCPP Gateway Mode: Client ID with which the cFos Charging Manager reports to the backend. |
| OCPP Gateway Connector ID | OCPP Gateway Mode: Display of the automatically assigned Connector ID. |
| OCPP Gateway SOCKS Host | URL of a SOCKS proxy, if the OCPP backend is accessed e.g. via a Smartmeter Gateway |
| OCPP Gateway SOCKS Authentication | Here you can select TLS if required |
| Deliver Charging Manager status as connector 0 | If activated, the status of the Charging Manager is sent to the backend as connector 0 of the wallbox |
| Use own certificates | If activated, an SSL certificate uploadable by you under Configuration is used. If deactivated, a self-signed standard certificate is used |
| Remote maintenance | If the wallbox has a web UI, you will be redirected to it when you click the "Remote maintenance" button |
| Alternative method | If the forwarding does not work, you can choose an alternative method. |
| User Charging rules | Here you can enter users and charging rules as described on the Charging rules page. You can also set the wallbox assignment of users in the user administration. |
